Plumbing for Beginners: What You Need for Installing a Bathtub
Plumbing for Beginners: What You Need for Installing a Bathtub
Blog Article
How do you actually feel on the subject of Installing A Bathtub?
Installing a bath tub isn't exactly brain surgery, however it does require solid plumbing, woodworking, as well as sometimes, tiling skills. Replacing an old bath tub with a new one is additionally a moderately tough project. If the old tub is conveniently accessible, the project can move immediately; if you have to open a wall to get rid of the old bathtub and position the brand-new bathtub, the task is much harder. In either situation, the task is within a house handyman's skills, although you will certainly require an assistant to vacate the old tub and embeded in the new one. Make sure you have actually qualified on your own for the work and fit attempting it. As opposed to employing a contractor to take control of a halfway-completed project, it is much better to consider using one prior to you start. Opportunities are you might need an expert plumber to make tube connections.
This write-up will certainly aid you install a brand-new bathtub in your shower room if you have actually currently acquired a new bathtub and also do not require to transform the plan of your previous supply of water pipes.
Your tools and product list need to make up the following:
Planning for the Setup
To start with, the supporting structure supplied with the bathroom must be fitted (if required) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to make certain that if the tap features a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps device to avoid strain on the tub.
Fit the flexible faucet adapters to the bottom of the two faucets using 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you ought to do is disconnect the supply of water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of getting rid of the existing taps can be quite bothersome because of the restricted accessibility that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a towel all set for the staying water that will originate from the pipes. Once the supply pipelines have been removed, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from turning during this process. As soon as the taps have actually been removed, the holes in the bath/basin will need to be cleansed of any old sealing substance.
Prior to moving on to fit the new taps, contrast the pipeline connections on the old taps to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Installing the Bath tub
Utilizing both wood boards under its feet, put the bath tub in the called for setting. The wood boards are helpful in evenly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 tiny points.
The next objective is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and also readjusting the feet on the bath tub till the level reviews degree.
To mount faucets, fit all-time low of the outermost versatile tap connector to the appropriate supply pipe by making a compression join; after that do the exact same for the other faucet.
Turn on the water supply and also inspect all joints and also new pipework for leaks and also tighten them if required. Fill up the bathtub and additionally examine the overflow outlet as well as the regular electrical outlet for leakages.
Finally, deal with the bath paneling as defined in the manufacturer's instruction manual. Tiling as well as sealing around the tub ought to wait up until the bath tub has actually been utilized at the very least when as this will settle it into its last placement.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, then you will certainly need reducing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the placing hole in the bath/basin guaranteeing that the washers remain in place in between the faucet as well as the sink. Safeguard the tap in position with the producer provided backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The previous kind should be linked to the faucet ends first, tightening just by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bath fulfills the tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to break a stiff seal, causing the water to pass through the wall surface in between the bathroom and also the tiling, leading to problems with moisture and also feasible leaks to the ceiling below.
You can choose from a selection of coloured sealants to blend in your components as well as fittings. They are offered in tubes and cartridges, and also can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water prior to sealing, to enable the movement experienced when the bathtub is in usage. The sealant can split fairly early if you do not take into account this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise quickly readily available on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I discovered that blog post on Tools You Need to Install a New Bathtub while perusing the internet. Sharing is nice. You never know, you may very well be helping someone out. Many thanks for going through it.
Fast and effective, call! Report this page